17 Protective Cover Manufacturers in 2024
This section provides an overview for protective covers as well as their applications and principles. Also, please take a look at the list of 17 protective cover manufacturers and their company rankings. Here are the top-ranked protective cover companies as of April, 2024: 1.elmex Controls Pvt Ltd., 2.TD Industrial Coverings, Inc., 3.Cunningham Covers.
Table of Contents
What Is a Protective Cover?
Protective Covers are used to protect the covers of vertical pipes such as manholes and hoardings. The upper end of a vertical water or sewage pipe has a hole for maintenance and cleaning, and if a load is applied to the covering, it may be damaged.
Protective coverings are classified according to their load capacity, and those that can withstand higher loads should be selected for installation in areas where large vehicles pass. The surface of the protective lid is installed so that it is at the same height as the road surface so that there are no steps on the road surface.
Uses of Protective Covers
Before wastewater from homes and businesses is discharged into the public sewer system, it is passed through a vertical pipe called a hoarding or pit. Once passed through the vertical pipe, large debris is allowed to settle out, preventing clogging of the sewer system.
Public sewers also have manholes for administrative purposes, and vertical pipes lead to waterways.
The tops of these vertical pipes have holes for internal maintenance and cleaning and are usually sealed with protective covers.
Principle of Protective Cover
The protective cover consists of a metal lid and a plastic base.
The load capacity of protective covers varies from product to product.
- T25: Withstands up to 25 tons. Used on roadways where vehicles of 14t or more pass through.
- T14: Withstands up to 14 tons. Used on roadways with few large vehicles.
- T8: Withstands up to 8 tons. Used on sidewalks and grounds where large vehicles will not pass over.
When installing the protective cover, the following points should be considered:
- To prevent the protective cover from coming into contact with the vertical pipe lid when it settles under load, a space of about 15 cm should be created between the lid of the vertical pipe and the protective cover.
- Install the protective cover so that its surface is at the same level as the road surface.
In order to meet the above requirements, the top opening of the vertical pipe is installed at a location that is excavated at least 15cm below the ground surface. A protective lid is placed on top of it, and the height of the pedestal is adjusted with granulated soil so that the surface of the protective lid is at the same height as the road surface.
Construction
When a new water pipe is installed or the protective cover needs to be replaced, a contractor is hired to install it.
The specific construction work for Protective Covers is carried out in the following steps:
- Foundation: Dig down around the top of the pipe to make room for the Protective Cover. To prevent the foundation from settling, granulated crushed stone is placed and carefully compacted. Grain-size-adjusted crushed stone is a rock that has been crushed and sieved to a uniform grain size. Because of its strength, it is used for the foundations of roads and railroad tracks.
- Installation: A pedestal and protective cover are placed on top of the foundation. Protective Covers should be installed level with the ground. If the ground itself is inclined, the inclination should be adjusted within the allowable inclination angle for each product.
- Backfill: Backfill around the piping and protective cover using granulated crushed stone or asphalt.
Locking and Baghole Types
Protective Covers are divided into Locking and Baghole types, depending on how they open and close. When opening the protective cover for inspection or cleaning, it is helpful to keep in mind the differences between the two types to avoid confusion.
- The locking type has a mechanism to secure the lid. The locking mechanism varies from product to product. Some have a key operated by a flat-blade screwdriver, while others have a hook-type bridle that is opened and closed with a crowbar. When opening, check the locking mechanism and use the appropriate method to unlock. When closing, if the lid is misaligned, it may not lock. Close the lid and lock it so that it does not move, and check that it is fixed.
- The baghole type is not equipped with a mechanism to secure the lid. There is a hole called a blind hole in the part where the lid and the pedestal meet. The operation is simpler than the locking type, but since there is no lock operation when closing, even if the lid is misaligned, it may be overlooked. Please be aware that if the lid is left in place, it may cause rainwater to flow in through the gaps or bad odors to leak out.
List of 17 Protective Cover Manufacturers
*Including some distributors, etc.
Sort by Features
- Default
- Company Size: largest first
- Year Founded: oldest first
- Year Founded: earliest first
Sort by Area
- United States of America
- Canada
- Czech Republic
- Germany
- India
- Netherlands
-
-
-
ifm efector, inc.
Protective cover
Manufacturer Overview
ifm efector (ifm) is a subsidiary of ifm electronic, founded in Germany in 1969. ifm has developed, manufactured and marketed sensors and controls technology to industries that include assembly and robotics, automotive, material handling, metal forming, mobile equipment, plastics, and food and beverage. Ifm produces sensors, condition monitoring equipment, image processing, safety technology, industrial communication, IO-link, systems for mobile machines, displays, software, connection technology, voltage supplies, as well as other accessories.
-
-
-
-
-
Creative Covers Inc.
Protective Covers
Manufacturer Overview
Creative Covers Inc., established in 1998 and based in Chicago, USA, is a manufacturer of custom and standard covers. The company offers covers for various applications, outdoor furniture and equipment protection. Its product range includes durable covers, outdoor patio furniture, and custom equipment covers tailored to individual specifications. It uses premium materials such as Sunbrella canvas and weatherman canvas and provides superior protection solutions that guarantee durability and elegance. The company caters to residential and commercial clients and delivers products that exceed expectations in functionality and aesthetics.
-
-
-
-
-
TD Industrial Coverings, Inc.
Protective Covers
Manufacturer Overview
TD Industrial Coverings, Inc., established in 1981 and based in Sterling Heights, MI, USA, is a manufacturer of protective covers for industrial and robotic applications. The company specializes in 3D prototyping and offers specialized solutions, including custom sewing and design for the automotive, aerospace, and medical sectors. It creates durable coverings for various industrial needs, particularly in robotic applications for painting and finishing processes. The company has established long-standing partnerships with major equipment suppliers such as Fanuc Robotics and ABB Robotics. Its class 100 clean room facility ensures that all products meet the highest quality and safety standards.
-
-
-
-
-
Custom Quality Manufacturing, Inc.
Protective Covers
Manufacturer Overview
Custom Quality Manufacturing, Inc., established in 1996 and based in the United States, is a manufacturer of custom protective covers for machinery. The company offers a range of products including flat and sewn bellows, scissor lift covers, and telescopic metal way covers. These covers are designed to shield machinery from contaminants like dust, oil, and debris, contributing to extended equipment lifespan and reduced maintenance costs. Its products serve automotive, robotics, and agriculture sectors. The company is known for its custom solutions and utilization of sturdy materials such as NCN40, NCN27, and PVC.
-
-
-
-
Manufacturer Overview
3M Company was founded in 1902 and is headquartered in St. Paul, Minnesota. 3M provides diversified technology services globally. 3M operates through four segments: Safety and Industrial, Transportation and Electronics, Health Care, and Consumer. The Safety and Industrial segment offerings include industrial abrasives, masking, and natural and color-coated mineral granules for shingles. The Transportation and Electronics segment offerings include ceramic solutions, light management films, and electronics assembly solutions. The Healthcare segment offerings include wound care, dentistry and orthodontia solutions, and filtration and purification systems. The Consumer segment offerings include consumer bandages, picture hanging, and stationery products.
-
-
-
-
-
Gary Manufacturing, Inc.
Protective Covers
Manufacturer Overview
Gary Manufacturing, Inc. was founded in 1958 in National City, California, USA, as a manufacturer of custom and commercial-sewn products. The product portfolio of the company consists of Coach Coordinates – RV Drapes, Clear Vinyl Industrial Curtains, Custom Industrial Equipment Covers, and GaryWear, among others. The products serve multiple purposes, including reducing the risk of accidents by preventing the spread of oil and grease from machinery, offering light control, and featuring plastic slider tabs on curtains for noiseless operation, as well as finding use in incontinence products. The company serves various industries, including military, aerospace, healthcare, medical, gyms, hotels, and hospitals.
-
-
-
-
-
Anubis 3D
SCARA COVER & BELLOW KIT
Manufacturer Overview
Anubis 3D Industrial Solutions Inc., established in 2014 and headquartered in Mississauga, Ontario, Canada, is an industrial component additive manufacturer and 3D printing service provider. The company's products include a wide range of end-of-arm tooling and robot accessories, as well as on-demand industrial components such as prototypes or low-volume production parts. It also provides 3D printing services that include selective laser sintering, stereolithography, and hybrid solutions. The company's services include custom manufacturing, including testing and design validation.
-
-
-
-
-
elmex Controls Pvt Ltd.
Protection covers
Manufacturer Overview
elmex Controls Pvt Ltd. has been a manufacturer of electrical components, founded in 1963 and headquartered in Vadodara, Gujarat, India. Specializing in terminal blocks, its offerings span screw, spring, and push-in terminal blocks, facilitating wire and cable connections. Additionally, the company provides an array of connectors, from wire-to-wire and wire-to-board to cable-to-cable connectors, serving various electrical component linkage needs. Complementing its range, the company offers essential components like fuses, switches, and relays for safeguarding and managing electrical circuits. Its pursuit of quality in operations and products has earned them several certifications such as ISO 9001, ATEX, DEMKO, and ISO 14001.
-
-
-
-
-
TRI-Dena
protective covers
Manufacturer Overview
Tri-Dena, established in 2014 and based in the Republic of Macedonia, is a textile product manufacturer. The company specializes in producing protective covers for various items including tables, chairs, refrigerators, and more, utilizing poly foam and PVC fabrics suitable for both indoor and outdoor furniture. These covers are designed to safeguard goods from potential damage and deterioration during storage and transportation. Additionally, the company offers customization options, allowing for the inclusion of client-specific labels and logos on the covers, fulfilling and delivering orders within a ten-day timeframe.
-
-
-
-
-
AERO COVERS
Protective Aircraft Covers
Manufacturer Overview
AERO COVERS, established in 1994 and based in Central Ontario, Canada, is a manufacturer of protective aircraft covers, marine covers, and windsocks. The company excels in creating durable aircraft wings, canopy, and cowl covers alongside custom marine upholstery and a diverse range of windsocks. It offers a diverse range of products, from high-grade, UV-resistant windsocks to stainless steel windsock frames and an array of aviation accessories. The company uses materials like DuPont SolarMax nylon and Delrin nylon bushings. Its products are sought after by aircraft owners across Canada, the USA, and numerous other countries.
-
-
-
-
-
Cunningham Covers
Protective Covers
Manufacturer Overview
Cunningham Covers, established in 1969 and based in the UK, is a manufacturer of protective covers. The company specializes in crafting a range of products including frost protection covers, waterproof covers, and the hot work habitat safe zone, and protect assets from environmental hazards and operational risks. These covers serve diverse industries such as oil & gas, transport, and aviation, and shields assets worldwide, from Asia and Africa to Australia. The company was honored with the prestigious Queen's Award for Enterprise.
-
-
-
-
-
-
-
Evotec Group
EVO COAT
-
-
-
-
-
-
Robot Protection Systems GmbH
PROTECTION SYSTEMS FOR ROBOTS
-
-
-
-
-
Dynatect Manufacturing, Inc.
Protective Covers
Company Overview
Dynatect Manufacturing, Inc. was founded in 1945 and is headquartered in New Berlin, Wisconsin. As a provider of custom motion and protection solutions, they cater to diverse industries, including manufacturing, automation, and medical. Its cutting-edge product range encompasses bellows, protective covers, and ball screw assemblies, vital for ensuring equipment longevity and operator safety. Dynatect's engineering expertise influenced sector advancements, finding applications from manufacturing facilities to medical equipment, ensuring smooth operations and enhanced safety.
-
-
-
-
-
EWAC
Covers for robots
Distributor Overview
Ewac, established in 1998 and headquartered in České Budějovice, Czech Republic, is a distributor and supplier of chemical products and technological equipment. The company's products include air filtration systems for vapors, liquids, or solid particles; industrial chemicals such as paints, varnishes, and emulsions; and paint shop equipment that includes robot covers, protective pads, and pH indicator strips. Its offering of technological equipment includes waste water treatment plants, EB and EBP containers, and pneumatic presses. Its services include supply chain management and the supply of spare parts.
-
-
Protective Cover Manufacturer Ranking
*Including some distributors, etc.Ranking as of April 2024
Derivation Method| Rank | Company | Click Share |
|---|---|---|
| 1 | elmex Controls Pvt Ltd. |
21.7%
|
| 2 | TD Industrial Coverings, Inc. |
13.0%
|
| 3 | Cunningham Covers |
13.0%
|
| 4 | Gary Manufacturing, Inc. |
13.0%
|
| 5 | TRI-Dena |
8.7%
|
| 6 | Creative Covers Inc. |
8.7%
|
| 7 | 3M |
8.7%
|
| 8 | Anubis 3D |
4.3%
|
| 9 | AERO COVERS |
4.3%
|
| 10 | Custom Quality Manufacturing, Inc. |
4.3%
|
Derivation Method
The ranking is calculated based on the click share within the protective cover page as of April 2024. Click share is defined as the total number of clicks for all companies during the period divided by the number of clicks for each company.Number of Employees
- EMKA Beschlagteile GmbH & Co. KG: 2,100
Newly Established Company
- TRI-Dena: 2014 (10 years ago)
- Creative Covers Inc.: 1998 (26 years ago)
- TD Industrial Coverings, Inc.: 1981 (43 years ago)
Company with a History
- EMKA Beschlagteile GmbH & Co. KG: 1932 (92 years ago)
- elmex Controls Pvt Ltd.: 1963 (61 years ago)
- TD Industrial Coverings, Inc.: 1981 (43 years ago)
Protective Cover Manufacturers in United States
*Including some distributors, etc.
- ifm efector, inc.
- Creative Covers Inc.
- TD Industrial Coverings, Inc.
- Custom Quality Manufacturing, Inc.
- 3M
- Gary Manufacturing, Inc.
Global Distribution of Protective Cover Manufacturers by Country
*Including some distributors, etc.
| Country | Number of Companies | Share (%) |
|---|---|---|
United States of America
|
6 | 54.5% |
Canada
|
1 | 9.1% |
India
|
1 | 9.1% |
Netherlands
|
1 | 9.1% |
Germany
|
1 | 9.1% |
Czech Republic
|
1 | 9.1% |
